Add a virtual global timer device driver. It uses a global timer
register as timer counter, and it uses mtimecmp CSR of clint as
interrupt source.
Using this virtul timer resolves dual way timer sync issue.
On dual way system, we should enable this driver and on single way
system, we should use standard risc-v clint timer.
1. Add a virtual global timer device driver, it is probed by fdt
sg2042-global-mtimer@70300101c0 {
compatible = "sophgo,sg2042-global-mtimer";
reg = < 0x00000070 0x300101c0 0x00000000 0x00000008
0x00000070 0xac000000 0x00000000 0x00200000>;
clock-frequency = <50000000 50000000>;
};
Its compatible should be "sophgo,sg2042-global-mtimer".
And the first region delcared in reg prop is the address of global
timer. The second region delcared in reg prop is the base of clint
timers.
The first clock in clock-frequency is the actual frequency of global
timer, the second clock is the actual frequency of clint timer.
2. Add a quirk in platform specific code.
Add a function sbi_platform_force_emulate_time_csr, it indicates if
opensbi should skip time CSR detection and make software in
supervisor and user mode use emulated time CSR.
Signed-off-by: Chao Wei <chao.wei@sophgo.com>
T-HEAD c9xx pmu only needs to clear OV bits of MCOUNTEROF when MOIP bit
of MIP is set, so correct the MIP value check to avoid race conditions
during processing interrupt.
In addition, the S-mode scounterof only have OV bit set when the related
bits of MCOUNTERWEN is set, so also configure MCOUNTERWEN to allow kernel
to access valid SCOUNTEROF.
Signed-off-by: haijiao.liu <haijiao.liu@sophgo.com>
The mango cpu of sophgo is a 64 cores C920 CPU. The board with mango can
have at most two sockets. The CPU have the following features:
1) support RV64GCV
2) one seperate timer each cluster
3) T-HEAD pmu device
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
add reboot and poweroff support. The whole reboot and shutdown
pm op includes shutdown jh7110 pmu device power domain
and access on board pmic register through I2C.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the system-suspend-test property is present in the domain config
node as shown below, implement system suspend with a simple 5 second
delay followed by a WFI. This allows testing system suspend when the
low-level firmware doesn't support it.
/ {
chosen {
opensbi-domains {
compatible = "opensbi,domain,config";
system-suspend-test;
};
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
On the Renesas RZ/Five SoC by default we want to configure 128MiB of memory
ranging from 0x58000000 as a non-cacheable + bufferable region in the PMA
and populate this region as PMA reserve DT node with shared DMA pool and
no-map flags set so that Linux drivers requesting any DMA'able memory go
through this region.
PMA node passed to the above stack:
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
I/O Coherence Port (IOCP) provides an AXI interface for connecting
external non-caching masters, such as DMA controllers. The accesses
from IOCP are coherent with D-Caches and L2 Cache.
IOCP is a specification option and is disabled on the Renesas RZ/Five
SoC due to this reason IP blocks using DMA will fail.
The Andes AX45MP core has a Programmable Physical Memory Attributes (PMA)
block that allows dynamic adjustment of memory attributes in the runtime.
It contains a configurable amount of PMA entries implemented as CSR
registers to control the attributes of memory locations in interest.
Below are the memory attributes supported:
* Device, Non-bufferable
* Device, bufferable
* Memory, Non-cacheable, Non-bufferable
* Memory, Non-cacheable, Bufferable
* Memory, Write-back, No-allocate
* Memory, Write-back, Read-allocate
* Memory, Write-back, Write-allocate
* Memory, Write-back, Read and Write-allocate
More info about PMA (section 10.3):
Link: http://www.andestech.com/wp-content/uploads/AX45MP-1C-Rev.-5.0.0-Datasheet.pdf
As a workaround for SoCs with IOCP disabled CMO needs to be handled by
software. Firstly OpenSBI configures the memory region as
"Memory, Non-cacheable, Bufferable" and passes this region as a global
shared dma pool as a DT node. With DMA_GLOBAL_POOL enabled all DMA
allocations happen from this region and synchronization callbacks are
implemented to synchronize when doing DMA transactions.
Example PMA region passed as a DT node from OpenSBI:
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As-per the SBI specification, the lower 24bits of the SBI vendor
extension id is same as lower 24bits of the mvendorid CSR.
We update the SBI vendor extension id checking based on above.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The code calls various macros from riscv_asm.h which is not directly
included. Fix such dependency.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The code calls various macros from riscv_asm.h and sbi_scratch.h
which are not directly included. Fix such dependency.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add D1's nonretentive suspend state to the devicetree so S-mode software
knows about it and can use it.
Latency and power measurements were taken on an Allwinner Nezha board:
- Entry latency was measured from the beginning of sbi_ecall_handler()
to before the call to wfi() in sun20i_d1_hart_suspend().
- Exit latency was measured from the beginning of sbi_init() to before
the call to sbi_hart_switch_mode() in init_warmboot().
- There was a 17.5 mW benefit from non-retentive suspend compared to
WFI, with a 170 mW cost during the 107 us entry/exit period. This
provides a break-even point around 1040 us. Residency includes entry
latency, so round this up to 1100 us.
- The hardware power sequence latency (after the WFI) is assumed to be
negligible, so set the wakeup latency to the exit latency.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Renesas RZ/Five RISC-V SoC has Instruction local memory and Data local
memory (ILM & DLM) mapped between region 0x30000 - 0x4FFFF. When a
virtual address falls within this range, the MMU doesn't trigger a page
fault; it assumes the virtual address is a physical address which can
cause undesired behaviours for statically linked applications/libraries.
To avoid this, add the ILM/DLM memory regions to the root domain region
of the PMPU with permissions set to 0x0 for S/U modes so that any access
to these regions gets blocked and for M-mode we grant full access (R/W/X).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add hart_start() and hart_stop() callbacks for the multi-core ae350
platform, it utilizes the ATCSMU to put the harts into power-gated
deep sleep mode. The programming sequence is stated as below:
1. Set the wakeup events to PCSm_WE
2. Set the sleep command to PCSm_CTL
3. Set the reset vector to HARTm_RESET_VECTOR_{LO|HI}
4. Write back and invalidate D-cache by executing the CCTL command L1D_WBINVAL_ALL
5. Disable I/D-cache by clearing mcache_ctl.{I|D}C_EN
6. Disable D-cache coherency by clearing mcache_ctl_.DC_COHEN
7. Wait for mcache_ctl.DC_COHSTA to be cleared to ensure the previous step is completed
8. Execute WFI
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch adds atcsmu support for Andes AE350 platforms. The SMU
provides system management capabilities, including clock, reset
and power control based on power domain partitions.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The two referenced commits passed incorrect bounds to the PLIC save/
restore functions, causing out-of-bounds memory access. The functions
expect "num" to be the 1-based number of interrupt sources, equivalent
to the "riscv,ndev" devicetree property. Thus, "num" must be strictly
smaller than the 0-based size of the array storing the register values.
However, the referenced commits incorrectly passed in the unmodified
size of the array as "num". Fix this by reducing PLIC_SOURCES (matching
"riscv,ndev" on this platform), while keeping the same array sizes.
Addresses-Coverity-ID: 1530251 ("Out-of-bounds access")
Addresses-Coverity-ID: 1530252 ("Out-of-bounds access")
Fixes: 8509e46ca6 ("lib: utils/irqchip: plic: Ensure no out-of-bound access in priority save/restore helpers")
Fixes: 9a2eeb4aae ("lib: utils/irqchip: plic: Ensure no out-of-bound access in context save/restore helpers")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
We add a generic platform override callback to allow platform specific
selection of cold boot HART.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
C language standard uses true/false for the boolean type.
Let's switch to that for better language compatibility.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Currently the context save/restore helpers writes/reads the provided
array using an index whose maximum value is determined by PLIC, which
potentially may disagree with the caller to these helpers.
Add a parameter to ask the caller to provide the size limit of the
array to ensure no out-of-bound access happens.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently the priority save/restore helpers writes/reads the provided
array using an index whose maximum value is determined by PLIC, which
potentially may disagree with the caller to these helpers.
Add a parameter to ask the caller to provide the size limit of the
array to ensure no out-of-bound access happens.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
It makes sense to use fdt_match_node() instead of fdt_find_match()
in fw_platform_lookup_special() as we already have the start offset
to search from.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We move andes directory to platform/generic as the necessary fdt
drivers are available, the users can enable the console, timer, ipi,
irqchip and reset devices by adding device tree nodes stated in the
docs/platform/andes-ae350.md.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Corrected the same parameter of writel_relaxed in sun20i_d1_riscv_cfg_init
to be u32 for a while and u64 for a while.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
With the T-HEAD C9XX cores being designed before or during ratification
of the SSCOFPMF extension, they implement a PMU extension that behaves
very similar but not equal to it by providing overflow interrupts though
in a slightly different registers format.
The sun20i-d1 is using this core. So implement the necessary overrides
to allow its pmu to be used via the standard sbi-pmu extension.
For now it's also the only soc using this core, so keep the additional
code in the d1-space for now.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Init of non-standard extensions is a platform-specific thing,
so allow generic platforms to do this via a platform-override.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We update generic platform to use kconfig for enabling/disabling
platform overrides. We also enable all platform overrides in generic
platform defconfig.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update gpio drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate gpio
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update i2c drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate i2c
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update irqchip drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate irqchip
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update ipi drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate ipi
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update timer drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate timer
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update reset drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate reset
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update serial drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate serial
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We extend the top-level makefile to allow kconfig based configuration
for each platform where each platform has it's own set of configs with
"defconfig" being the default config.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
