Add interface to support Power Sourcing Equipment. At current step it
provides generic way to address all variants of PSE devices as defined
in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4
PoDL Power Sourcing Equipment (PSE).
Currently supported and mandatory objects are:
IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus
IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl
This is minimal interface needed to control PSE on each separate
ethernet port but it provides not all mandatory objects specified in
IEEE 802.3-2018.
Since "PoDL PSE" and "PSE" have similar names, but some different values
I decide to not merge them and keep separate naming schema. This should
allow as to be as close to IEEE 802.3 spec as possible and avoid name
conflicts in the future.
This implementation is connected to PHYs instead of MACs because PSE
auto classification can potentially interfere with PHY auto negotiation.
So, may be some extra PHY related initialization will be needed.
With WIP version of ethtools interaction with PSE capable link looks
as following:
$ ip l
...
5: t1l1@eth0: <BROADCAST,MULTICAST> ..
...
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: disabled
PoDL PSE Power Detection Status: disabled
$ ethtool --set-pse t1l1 podl-pse-admin-control enable
$ ethtool --show-pse t1l1
PSE attributs for t1l1:
PoDL PSE Admin State: enabled
PoDL PSE Power Detection Status: delivering power
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2022-10-03
We've added 10 non-merge commits during the last 23 day(s) which contain
a total of 14 files changed, 130 insertions(+), 69 deletions(-).
The main changes are:
1) Fix dynptr helper API to gate behind CAP_BPF given it was not intended
for unprivileged BPF programs, from Kumar Kartikeya Dwivedi.
2) Fix need_wakeup flag inheritance from umem buffer pool for shared xsk
sockets, from Jalal Mostafa.
3) Fix truncated last_member_type_id in btf_struct_resolve() which had a
wrong storage type, from Lorenz Bauer.
4) Fix xsk back-pressure mechanism on tx when amount of produced
descriptors to CQ is lower than what was grabbed from xsk tx ring,
from Maciej Fijalkowski.
5) Fix wrong cgroup attach flags being displayed to effective progs,
from Pu Lehui.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xsk: Inherit need_wakeup flag for shared sockets
bpf: Gate dynptr API behind CAP_BPF
selftests/bpf: Adapt cgroup effective query uapi change
bpftool: Fix wrong cgroup attach flags being assigned to effective progs
bpf, cgroup: Reject prog_attach_flags array when effective query
bpf: Ensure correct locking around vulnerable function find_vpid()
bpf: btf: fix truncated last_member_type_id in btf_struct_resolve
selftests/xsk: Add missing close() on netns fd
xsk: Fix backpressure mechanism on Tx
MAINTAINERS: Add include/linux/tnum.h to BPF CORE
====================
Link: https://lore.kernel.org/r/20221003201957.13149-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-10-03
We've added 143 non-merge commits during the last 27 day(s) which contain
a total of 151 files changed, 8321 insertions(+), 1402 deletions(-).
The main changes are:
1) Add kfuncs for PKCS#7 signature verification from BPF programs, from Roberto Sassu.
2) Add support for struct-based arguments for trampoline based BPF programs,
from Yonghong Song.
3) Fix entry IP for kprobe-multi and trampoline probes under IBT enabled, from Jiri Olsa.
4) Batch of improvements to veristat selftest tool in particular to add CSV output,
a comparison mode for CSV outputs and filtering, from Andrii Nakryiko.
5) Add preparatory changes needed for the BPF core for upcoming BPF HID support,
from Benjamin Tissoires.
6) Support for direct writes to nf_conn's mark field from tc and XDP BPF program
types, from Daniel Xu.
7) Initial batch of documentation improvements for BPF insn set spec, from Dave Thaler.
8) Add a new BPF_MAP_TYPE_USER_RINGBUF map which provides single-user-space-producer /
single-kernel-consumer semantics for BPF ring buffer, from David Vernet.
9) Follow-up fixes to BPF allocator under RT to always use raw spinlock for the BPF
hashtab's bucket lock, from Hou Tao.
10) Allow creating an iterator that loops through only the resources of one
task/thread instead of all, from Kui-Feng Lee.
11) Add support for kptrs in the per-CPU arraymap, from Kumar Kartikeya Dwivedi.
12) Add a new kfunc helper for nf to set src/dst NAT IP/port in a newly allocated CT
entry which is not yet inserted, from Lorenzo Bianconi.
13) Remove invalid recursion check for struct_ops for TCP congestion control BPF
programs, from Martin KaFai Lau.
14) Fix W^X issue with BPF trampoline and BPF dispatcher, from Song Liu.
15) Fix percpu_counter leakage in BPF hashtab allocation error path, from Tetsuo Handa.
16) Various cleanups in BPF selftests to use preferred ASSERT_* macros, from Wang Yufen.
17) Add invocation for cgroup/connect{4,6} BPF programs for ICMP pings, from YiFei Zhu.
18) Lift blinding decision under bpf_jit_harden = 1 to bpf_capable(), from Yauheni Kaliuta.
19) Various libbpf fixes and cleanups including a libbpf NULL pointer deref, from Xin Liu.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (143 commits)
net: netfilter: move bpf_ct_set_nat_info kfunc in nf_nat_bpf.c
Documentation: bpf: Add implementation notes documentations to table of contents
bpf, docs: Delete misformatted table.
selftests/xsk: Fix double free
bpftool: Fix error message of strerror
libbpf: Fix overrun in netlink attribute iteration
selftests/bpf: Fix spelling mistake "unpriviledged" -> "unprivileged"
samples/bpf: Fix typo in xdp_router_ipv4 sample
bpftool: Remove unused struct event_ring_info
bpftool: Remove unused struct btf_attach_point
bpf, docs: Add TOC and fix formatting.
bpf, docs: Add Clang note about BPF_ALU
bpf, docs: Move Clang notes to a separate file
bpf, docs: Linux byteswap note
bpf, docs: Move legacy packet instructions to a separate file
selftests/bpf: Check -EBUSY for the recurred bpf_setsockopt(TCP_CONGESTION)
bpf: tcp: Stop bpf_setsockopt(TCP_CONGESTION) in init ops to recur itself
bpf: Refactor bpf_setsockopt(TCP_CONGESTION) handling into another function
bpf: Move the "cdg" tcp-cc check to the common sol_tcp_sockopt()
bpf: Add __bpf_prog_{enter,exit}_struct_ops for struct_ops trampoline
...
====================
Link: https://lore.kernel.org/r/20221003194915.11847-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KVM/arm64 updates for v6.1
- Fixes for single-stepping in the presence of an async
exception as well as the preservation of PSTATE.SS
- Better handling of AArch32 ID registers on AArch64-only
systems
- Fixes for the dirty-ring API, allowing it to work on
architectures with relaxed memory ordering
- Advertise the new kvmarm mailing list
- Various minor cleanups and spelling fixes
Steffen Klassert says:
====================
1) Refactor selftests to use an array of structs in xfrm_fill_key().
From Gautam Menghani.
2) Drop an unused argument from xfrm_policy_match.
From Hongbin Wang.
3) Support collect metadata mode for xfrm interfaces.
From Eyal Birger.
4) Add netlink extack support to xfrm.
From Sabrina Dubroca.
Please note, there is a merge conflict in:
include/net/dst_metadata.h
between commit:
0a28bfd497 ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support")
from the net-next tree and commit:
5182a5d48c ("net: allow storing xfrm interface metadata in metadata_dst")
from the ipsec-next tree.
Can be solved as done in linux-next.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IORING_URING_CMD_FIXED flag that is to be used for sending io_uring
command with previously registered buffers. User-space passes the buffer
index in sqe->buf_index, same as done in read/write variants that uses
fixed buffers.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Link: https://lore.kernel.org/r/20220930062749.152261-3-anuj20.g@samsung.com
[axboe: shuffle valid flags check before acting on it]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* for-6.1/block: (162 commits)
sbitmap: fix lockup while swapping
block: add rationale for not using blk_mq_plug() when applicable
block: adapt blk_mq_plug() to not plug for writes that require a zone lock
s390/dasd: use blk_mq_alloc_disk
blk-cgroup: don't update the blkg lookup hint in blkg_conf_prep
nvmet: don't look at the request_queue in nvmet_bdev_set_limits
nvmet: don't look at the request_queue in nvmet_bdev_zone_mgmt_emulate_all
blk-mq: use quiesced elevator switch when reinitializing queues
block: replace blk_queue_nowait with bdev_nowait
nvme: remove nvme_ctrl_init_connect_q
nvme-loop: use the tagset alloc/free helpers
nvme-loop: store the generic nvme_ctrl in set->driver_data
nvme-loop: initialize sqsize later
nvme-fc: use the tagset alloc/free helpers
nvme-fc: store the generic nvme_ctrl in set->driver_data
nvme-fc: keep ctrl->sqsize in sync with opts->queue_size
nvme-rdma: use the tagset alloc/free helpers
nvme-rdma: store the generic nvme_ctrl in set->driver_data
nvme-tcp: use the tagset alloc/free helpers
nvme-tcp: store the generic nvme_ctrl in set->driver_data
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IEEE 802.1Q clause 12.29.1.1 "The queueMaxSDUTable structure and data
types" and 8.6.8.4 "Enhancements for scheduled traffic" talk about the
existence of a per traffic class limitation of maximum frame sizes, with
a fallback on the port-based MTU.
As far as I am able to understand, the 802.1Q Service Data Unit (SDU)
represents the MAC Service Data Unit (MSDU, i.e. L2 payload), excluding
any number of prepended VLAN headers which may be otherwise present in
the MSDU. Therefore, the queueMaxSDU is directly comparable to the
device MTU (1500 means L2 payload sizes are accepted, or frame sizes of
1518 octets, or 1522 plus one VLAN header). Drivers which offload this
are directly responsible of translating into other units of measurement.
To keep the fast path checks optimized, we keep 2 arrays in the qdisc,
one for max_sdu translated into frame length (so that it's comparable to
skb->len), and another for offloading and for dumping back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nlmsg_flags are full of historical baggage, inconsistencies and
strangeness. Try to document it more thoroughly. Explain the meaning
of the ECHO flag (and while at it clarify the comment in the uAPI).
Handwave a little about the NEW request flags and how they make
sense on the surface but cater to really old paradigm before commands
were a thing.
I will add more notes on how to make use of ECHO and discouragement
for reuse of flags to the kernel-side documentation.
Link: https://lore.kernel.org/r/20220927212306.823862-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PERF_MEM_LVLNUM_EXTN_MEM which can be used to indicate accesses to
extension memory like CXL etc. PERF_MEM_LVL_IO can be used for IO
accesses but it can not distinguish between local and remote IO.
Introduce new field PERF_MEM_LVLNUM_IO which can be clubbed with
PERF_MEM_REMOTE_REMOTE to indicate Remote IO accesses.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220928095805.596-2-ravi.bangoria@amd.com
In order to differenciate between architectures that require no extra
synchronisation when accessing the dirty ring and those who do,
add a new capability (KVM_CAP_DIRTY_LOG_RING_ACQ_REL) that identify
the latter sort. TSO architectures can obviously advertise both, while
relaxed architectures must only advertise the ACQ_REL version.
This requires some configuration symbol rejigging, with HAVE_KVM_DIRTY_RING
being only indirectly selected by two top-level config symbols:
- HAVE_KVM_DIRTY_RING_TSO for strongly ordered architectures (x86)
- HAVE_KVM_DIRTY_RING_ACQ_REL for weakly ordered architectures (arm64)
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20220926145120.27974-3-maz@kernel.org
Allow creating an iterator that loops through resources of one
thread/process.
People could only create iterators to loop through all resources of
files, vma, and tasks in the system, even though they were interested
in only the resources of a specific task or process. Passing the
additional parameters, people can now create an iterator to go
through all resources or only the resources of a task.
Signed-off-by: Kui-Feng Lee <kuifeng@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/bpf/20220926184957.208194-2-kuifeng@fb.com
Changing return value of kprobe's version of bpf_get_func_ip
to return zero if the attach address is not on the function's
entry point.
For kprobes attached in the middle of the function we can't easily
get to the function address especially now with the CONFIG_X86_KERNEL_IBT
support.
If user cares about current IP for kprobes attached within the
function body, they can get it with PT_REGS_IP(ctx).
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martynas Pumputis <m@lambda.lt>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220926153340.1621984-6-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently we only have 3 qgroup flags:
- BTRFS_QGROUP_STATUS_FLAG_ON
- BTRFS_QGROUP_STATUS_FLAG_RESCAN
- BTRFS_QGROUP_STATUS_FLAG_INCONSISTENT
These flags match the on-disk flags used in btrfs_qgroup_status.
But we're going to introduce extra runtime flags which will not reach
disks.
So here we introduce a new mask, BTRFS_QGROUP_STATUS_FLAGS_MASK, to
make sure only those flags can reach disks.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The problem of long mount time caused by block group item search is
already known for some time, and the solution of block group tree has
been proposed.
There is really no need to bound this feature into extent tree v2, just
introduce compat RO flag, BLOCK_GROUP_TREE, to correctly solve the
problem.
All the code handling block group root is already in the upstream
kernel, thus this patch really only needs to introduce the new compat RO
flag.
This patch introduces one extra artificial limitation on block group
tree feature, that free space cache v2 and no-holes feature must be
enabled to use this new compat RO feature.
This artificial requirement is mostly to reduce the test combinations,
and can be a guideline for future features, to mostly rely on the latest
default features.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add support for this new CEC message. This was added in HDMI 2.1a.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is basically equivalent to the FUSE_CREATE operation which creates and
opens a regular file.
Add a new FUSE_TMPFILE operation, otherwise just reuse the protocol and the
code for FUSE_CREATE.
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
START_USER_RECOVERY and END_USER_RECOVERY are two new control commands
to support user recovery feature.
After a crash, user should send START_USER_RECOVERY, it will:
(1) check if (a)current ublk_device is UBLK_S_DEV_QUIESCED which was
set by quiesce_work and (b)chardev is released
(2) reinit all ubqs, including:
(a) put the task_struct and reset ->ubq_daemon to NULL.
(b) reset all ublk_io.
(3) reset ub->mm to NULL.
Then, user should start a new process and send FETCH_REQ on each
ubq_daemon.
Finally, user should send END_USER_RECOVERY, it will:
(1) wait for all new ubq_daemons getting ready.
(2) update ublksrv_pid
(3) unquiesce the request queue and expect incoming ublk_queue_rq()
(4) convert ub's state to UBLK_S_DEV_LIVE
Note: we can handle STOP_DEV between START_USER_RECOVERY and
END_USER_RECOVERY. This is helpful to users who cannot start new process
after sending START_USER_RECOVERY ctrl-cmd.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-7-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
UBLK_F_USER_RECOVERY_REISSUE implies that:
With a dying ubq_daemon, ublk_drv let monitor_work requeues rq issued to
userspace(ublksrv) before the ubq_daemon is dying.
UBLK_F_USER_RECOVERY_REISSUE is designed for backends which:
(1) tolerate double-write since ublk_drv may issue the same rq
twice.
(2) does not let frontend users get I/O error, such as read-only FS
and VM backend.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-6-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define some macros for recovery feature.
UBLK_S_DEV_QUIESCED implies that ublk_device is quiesced
and is ready for recovery. This state can be observed by userspace.
UBLK_F_USER_RECOVERY implies that:
(1) ublk_drv enables recovery feature. It won't let monitor_work to
automatically abort rqs and release the device.
(2) With a dying ubq_daemon, ublk_drv ends(aborts) rqs issued to
userspace(ublksrv) before crash.
(3) With a dying ubq_daemon, in task work and ublk_queue_rq(),
ublk_drv requeues rqs.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-3-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This change adds support for not enabling carrier during TUNSETIFF
interface creation by specifying the IFF_NO_CARRIER flag.
Our tests make heavy use of tun interfaces. In some scenarios, the test
process creates the interface but another process brings it up after the
interface is discovered via netlink notification. In that case, it is
not possible to create a tun/tap interface with carrier off without it
racing against the bring up. Immediately setting carrier off via
TUNSETCARRIER is still too late.
Signed-off-by: Patrick Rohr <prohr@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a prior change, we added a new BPF_MAP_TYPE_USER_RINGBUF map type which
will allow user-space applications to publish messages to a ring buffer
that is consumed by a BPF program in kernel-space. In order for this
map-type to be useful, it will require a BPF helper function that BPF
programs can invoke to drain samples from the ring buffer, and invoke
callbacks on those samples. This change adds that capability via a new BPF
helper function:
bpf_user_ringbuf_drain(struct bpf_map *map, void *callback_fn, void *ctx,
u64 flags)
BPF programs may invoke this function to run callback_fn() on a series of
samples in the ring buffer. callback_fn() has the following signature:
long callback_fn(struct bpf_dynptr *dynptr, void *context);
Samples are provided to the callback in the form of struct bpf_dynptr *'s,
which the program can read using BPF helper functions for querying
struct bpf_dynptr's.
In order to support bpf_ringbuf_drain(), a new PTR_TO_DYNPTR register
type is added to the verifier to reflect a dynptr that was allocated by
a helper function and passed to a BPF program. Unlike PTR_TO_STACK
dynptrs which are allocated on the stack by a BPF program, PTR_TO_DYNPTR
dynptrs need not use reference tracking, as the BPF helper is trusted to
properly free the dynptr before returning. The verifier currently only
supports PTR_TO_DYNPTR registers that are also DYNPTR_TYPE_LOCAL.
Note that while the corresponding user-space libbpf logic will be added
in a subsequent patch, this patch does contain an implementation of the
.map_poll() callback for BPF_MAP_TYPE_USER_RINGBUF maps. This
.map_poll() callback guarantees that an epoll-waiting user-space
producer will receive at least one event notification whenever at least
one sample is drained in an invocation of bpf_user_ringbuf_drain(),
provided that the function is not invoked with the BPF_RB_NO_WAKEUP
flag. If the BPF_RB_FORCE_WAKEUP flag is provided, a wakeup
notification is sent even if no sample was drained.
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220920000100.477320-3-void@manifault.com
We want to support a ringbuf map type where samples are published from
user-space, to be consumed by BPF programs. BPF currently supports a
kernel -> user-space circular ring buffer via the BPF_MAP_TYPE_RINGBUF
map type. We'll need to define a new map type for user-space -> kernel,
as none of the helpers exported for BPF_MAP_TYPE_RINGBUF will apply
to a user-space producer ring buffer, and we'll want to add one or
more helper functions that would not apply for a kernel-producer
ring buffer.
This patch therefore adds a new BPF_MAP_TYPE_USER_RINGBUF map type
definition. The map type is useless in its current form, as there is no
way to access or use it for anything until we one or more BPF helpers. A
follow-on patch will therefore add a new helper function that allows BPF
programs to run callbacks on samples that are published to the ring
buffer.
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220920000100.477320-2-void@manifault.com
Attach flags is only valid for attached progs of this layer cgroup,
but not for effective progs. For querying with EFFECTIVE flags,
exporting attach flags does not make sense. So when effective query,
we reject prog_attach_flags array and don't need to populate it.
Also we limit attach_flags to output 0 during effective query.
Fixes: b79c9fc955 ("bpf: implement BPF_PROG_QUERY for BPF_LSM_CGROUP")
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20220921104604.2340580-2-pulehui@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Add IIO_MOD_LINEAR_X, IIO_MOD_LINEAR_Y and IIO_MOD_LINEAR_Z modifiers to te
IIO core, which is preparatory for adding the Bosch BNO055 IMU driver.
Bosch BNO055 IMU can report raw accelerations (among x, y and z axis) as
well as the so called "linear accelerations" (again, among x, y and z axis)
which is basically the acceleration after subtracting gravity and for which
those new modifiers are for.
Signed-off-by: Andrea Merello <andrea.merello@iit.it>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220907132205.28021-2-andrea.merello@iit.it
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow deferring async tasks until the user calls io_uring_enter(2) with
the IORING_ENTER_GETEVENTS flag. Enable this mode with a flag at
io_uring_setup time. This functionality requires that the later
io_uring_enter will be called from the same submission task, and therefore
restrict this flag to work only when IORING_SETUP_SINGLE_ISSUER is also
set.
Being able to hand pick when tasks are run prevents the problem where
there is current work to be done, however task work runs anyway.
For example, a common workload would obtain a batch of CQEs, and process
each one. Interrupting this to additional taskwork would add latency but
not gain anything. If instead task work is deferred to just before more
CQEs are obtained then no additional latency is added.
The way this is implemented is by trying to keep task work local to a
io_ring_ctx, rather than to the submission task. This is required, as the
application will want to wake up only a single io_ring_ctx at a time to
process work, and so the lists of work have to be kept separate.
This has some other benefits like not having to check the task continually
in handle_tw_list (and potentially unlocking/locking those), and reducing
locks in the submit & process completions path.
There are networking cases where using this option can reduce request
latency by 50%. For example a contrived example using [1] where the client
sends 2k data and receives the same data back while doing some system
calls (to trigger task work) shows this reduction. The reason ends up
being that if sending responses is delayed by processing task work, then
the client side sits idle. Whereas reordering the sends first means that
the client runs it's workload in parallel with the local task work.
[1]:
Using https://github.com/DylanZA/netbench/tree/defer_run
Client:
./netbench --client_only 1 --control_port 10000 --host <host> --tx "epoll --threads 16 --per_thread 1 --size 2048 --resp 2048 --workload 1000"
Server:
./netbench --server_only 1 --control_port 10000 --rx "io_uring --defer_taskrun 0 --workload 100" --rx "io_uring --defer_taskrun 1 --workload 100"
Signed-off-by: Dylan Yudaken <dylany@fb.com>
Link: https://lore.kernel.org/r/20220830125013.570060-5-dylany@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.1
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
iio: accel: bma400: Add support for single and double tap events
iio: Add new event type gesture and use direction for single and double tap
iio: Use per-device lockdep class for mlock
iio: adc: add max11205 adc driver
dt-bindings: iio: adc: Add max11205 documentation file
iio: magnetometer: yamaha-yas530: Use dev_err_probe()
iio: magnetometer: yamaha-yas530: Make strings const in chip info
iio: magnetometer: yamaha-yas530: Use pointers as driver data
iio: adc: tsc2046: silent spi_device_id warning
iio: adc: tsc2046: add vref support
dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
iio: light: ltrf216a: Add raw attribute
dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
MAINTAINERS: fix Analog Devices forum links
iio/accel: fix repeated words in comments
dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
iio: add MEMSensing MSA311 3-axis accelerometer driver
dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
...
When the SPDX-License-Identifier tag has been added, the corresponding
license text has not been removed.
Remove it now.
Also, in xt_connmark.h, move the copyright text at the top of the file
which is a much more common pattern.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Florian Westphal <fw@strlen.de>
This allows to export the type in BTF and so in the automatically
generated vmlinux.h. It will also add some static checks on the users
when we change the ll driver API (see not below).
Note that we need to also do change in the ll_driver API, but given
that this will have a wider impact outside of this tree, we leave this
as a TODO for the future.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220902132938.2409206-11-benjamin.tissoires@redhat.com
When we are dealing with eBPF, we need to have access to the report type.
Currently our implementation differs from the USB standard, making it
impossible for users to know the exact value besides hardcoding it
themselves.
And instead of a blank define, convert it as an enum.
Note that we need to also do change in the ll_driver API, but given
that this will have a wider impact outside of this tree, we leave this
as a TODO for the future.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220902132938.2409206-10-benjamin.tissoires@redhat.com
The NEXT-C-SID mechanism described in [1] offers the possibility of
encoding several SRv6 segments within a single 128 bit SID address. Such
a SID address is called a Compressed SID (C-SID) container. In this way,
the length of the SID List can be drastically reduced.
A SID instantiated with the NEXT-C-SID flavor considers an IPv6 address
logically structured in three main blocks: i) Locator-Block; ii)
Locator-Node Function; iii) Argument.
C-SID container
+------------------------------------------------------------------+
| Locator-Block |Loc-Node| Argument |
| |Function| |
+------------------------------------------------------------------+
<--------- B -----------> <- NF -> <------------- A --------------->
(i) The Locator-Block can be any IPv6 prefix available to the provider;
(ii) The Locator-Node Function represents the node and the function to
be triggered when a packet is received on the node;
(iii) The Argument carries the remaining C-SIDs in the current C-SID
container.
The NEXT-C-SID mechanism relies on the "flavors" framework defined in
[2]. The flavors represent additional operations that can modify or
extend a subset of the existing behaviors.
This patch introduces the support for flavors in SRv6 End behavior
implementing the NEXT-C-SID one. An SRv6 End behavior with NEXT-C-SID
flavor works as an End behavior but it is capable of processing the
compressed SID List encoded in C-SID containers.
An SRv6 End behavior with NEXT-C-SID flavor can be configured to support
user-provided Locator-Block and Locator-Node Function lengths. In this
implementation, such lengths must be evenly divisible by 8 (i.e. must be
byte-aligned), otherwise the kernel informs the user about invalid
values with a meaningful error code and message through netlink_ext_ack.
If Locator-Block and/or Locator-Node Function lengths are not provided
by the user during configuration of an SRv6 End behavior instance with
NEXT-C-SID flavor, the kernel will choose their default values i.e.,
32-bit Locator-Block and 16-bit Locator-Node Function.
[1] - https://datatracker.ietf.org/doc/html/draft-ietf-spring-srv6-srh-compression
[2] - https://datatracker.ietf.org/doc/html/rfc8986
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some DSA switches have multiple CPU ports, which can be used to improve
CPU termination throughput, but DSA, through dsa_tree_setup_cpu_ports(),
sets up only the first one, leading to suboptimal use of hardware.
The desire is to not change the default configuration but to permit the
user to create a dynamic mapping between individual user ports and the
CPU port that they are served by, configurable through rtnetlink. It is
also intended to permit load balancing between CPU ports, and in that
case, the foreseen model is for the DSA master to be a bonding interface
whose lowers are the physical DSA masters.
To that end, we create a struct rtnl_link_ops for DSA user ports with
the "dsa" kind. We expose the IFLA_DSA_MASTER link attribute that
contains the ifindex of the newly desired DSA master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for matching on L2TPv3 session ID.
Session ID can be specified only when ip proto was
set to IPPROTO_L2TP.
Example filter:
# tc filter add dev $PF1 ingress prio 1 protocol ip \
flower \
ip_proto l2tp \
l2tpv3_sid 1234 \
skip_sw \
action mirred egress redirect dev $VF1_PR
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
