commit 08ce9a1b72 upstream.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Co-Developed-by: Maxim Popov <maxim.snafu@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231123072818.1394539-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0b9d97a77 upstream.
The console is immediately assigned to the ma35d1 port without
checking its index. This oversight can lead to out-of-bounds
errors when the index falls outside the valid '0' to
MA35_UART_NR range. Such scenario trigges ran error like the
following:
UBSAN: array-index-out-of-bounds in drivers/tty/serial/ma35d1_serial.c:555:51
index -1 is out of range for type 'uart_ma35d1_port [17]
Check the index before using it and bail out with a warning.
Fixes: 930cbf92db ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Cc: Jacky Huang <ychuang3@nuvoton.com>
Cc: <stable@vger.kernel.org> # v6.5+
Link: https://lore.kernel.org/r/20231204163804.1331415-2-andi.shyti@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4876dacac upstream.
Some of the later revisions of the Brainboxes PX cards are based
on the Oxford Semiconductor chipset. Due to the chip's unique setup
these cards need to be initialised.
Previously these were tested against a reference card with the same broken
baudrate on another PC, cancelling out the effect. With this patch they
work and can transfer/receive find against an FTDI-based device.
Add all of the cards which require this setup to the quirks table.
Thanks to Maciej W. Rozycki for clarification on this chip.
Fixes: ef5a03a26c ("tty: 8250: Add support for Brainboxes PX cards.")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Link: https://lore.kernel.org/r/DU0PR02MB7899D222A4AB2A4E8C57108FC4DBA@DU0PR02MB7899.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a6261 ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a6261 ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 44b27aec9d ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d8 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d8376 ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
