[ Upstream commit d12d635bb0 ]
Switching to a different reset sequence, enabling IOVCC before enabling
VCC.
There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of
panel-simple") I moved a pile of panels out of panel-simple driver
into the newly created panel-edp driver. One of those panels, however,
shouldn't have been moved.
As is clear from commit e35e305eff ("drm/panel: simple: Add AUO
B116XW03 panel support"), AUX B116XW03 is an LVDS panel. It's used in
exynos5250-snow and exynos5420-peach-pit where it's clear that the
panel is hooked up with LVDS. Furthermore, searching for datasheets I
found one that makes it clear that this panel is LVDS.
As far as I can tell, I got confused because in commit 88d3457ceb
("drm/panel: auo,b116xw03: fix flash backlight when power on") Jitao
Shi added "DRM_MODE_CONNECTOR_eDP". That seems wrong. Looking at the
downstream ChromeOS trees, it seems like some Mediatek boards are
using a panel that they call "auo,b116xw03" that's an eDP panel. The
best I can guess is that they actually have a different panel that has
similar timing. If so then the proper panel should be used or they
should switch to the generic "edp-panel" compatible.
When moving this back to panel-edp, I wasn't sure what to use for
.bus_flags and .bus_format and whether to add the extra "enable" delay
from commit 88d3457ceb ("drm/panel: auo,b116xw03: fix flash
backlight when power on"). I've added formats/flags/delays based on my
(inexpert) analysis of the datasheet. These are untested.
NOTE: if/when this is backported to stable, we might run into some
trouble. Specifically, before 474c162878 ("arm64: dts: mt8183:
jacuzzi: Move panel under aux-bus") this panel was used by
"mt8183-kukui-jacuzzi", which assumed it was an eDP panel. I don't
know what to suggest for that other than someone making up a bogus
panel for jacuzzi that's just for the stable channel.
Fixes: 88d3457ceb ("drm/panel: auo,b116xw03: fix flash backlight when power on")
Fixes: 5f04e7ce39 ("drm/panel-edp: Split eDP panels out of panel-simple")
Tested-by: Anton Bambura <jenneron@postmarketos.org>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925150010.1.Iff672233861bcc4cf25a7ad0a81308adc3bda8a4@changeid
This panel has been implemented in commit eae7488814 ("drm/panel-simple:
Add Innolux G156HCE-L01 panel entry") with a higher clock than the typical
one mentioned on the documentation to avoid flickering on the unit
tested. Testing on a different unit shows that the panel actually works
with the intended 70.93 MHz clock and even lower frequencies so the
flickering is likely caused either by a defective unit or by other
different components such as the bridge.
Fixes: eae7488814 ("drm/panel-simple: Add Innolux G156HCE-L01 panel entry")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Vasut <marex@denx.de> # MX8MM with LT9211
Reviewed-by: Marek Vasut <marex@denx.de>
[narmstrong: fixed commit id in commit msg]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814134024.397739-1-luca.ceresoli@bootlin.com
Commit 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4
panel") added support for this panel model, but the timings it implements
are very different from what the datasheet describes. I checked both the
G121EAN01.0 datasheet from [0] and the G121EAN01.4 one from [1] and they
all have the same timings: for example the LVDS clock typical value is 74.4
MHz, not 66.7 MHz as implemented.
Replace the timings with the ones from the documentation. These timings
have been tested and the clock frequencies verified with an oscilloscope to
ensure they are correct.
Also use struct display_timing instead of struct drm_display_mode in order
to also specify the minimum and maximum values.
[0] https://embedded.avnet.com/product/g121ean01-0/
[1] https://embedded.avnet.com/product/g121ean01-4/
Fixes: 03e909acd9 ("drm/panel: simple: Add support for AUO G121EAN01.4 panel")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804151239.835216-1-luca.ceresoli@bootlin.com
A very basic debugging rule when a device is connected for the first
time is to access a read-only register which contains known data in
order to ensure the communication protocol is properly working. This
driver lacked any read helper which is often a critical piece for
speeding-up bring-ups.
Add a read helper and use it to verify the communication with the panel
is working as soon as possible in order to inform the user early if this
is not the case.
As this panel may work with no MISO line, the check is discarded in this
case. Upon error, we do not fail probing but just warn the user, in case
the DT description would be lacking the Rx bus width (which is likely on
old descriptions) in order to avoid breaking existing devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org> # no MISO line
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-20-sre@kernel.org
This panel from Emerging Display Technologies Corporation features an
ST7789V2 LCD controller panel inside which is almost identical to what
the Sitronix panel driver supports.
In practice, the module physical size is specific, and experiments show
that the display will malfunction if any of the following situation
occurs:
* Pixel clock is above 3MHz
* Pixel clock is not inverted
I could not properly identify the reasons behind these failures, scope
captures show valid input signals.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714013756.1546769-19-sre@kernel.org
The newly added driver only builds when DRM_DISPLAY_DP_HELPER is enabled:
x86_64-linux-ld: drivers/gpu/drm/panel/panel-visionox-r66451.o: in function `visionox_r66451_enable':
panel-visionox-r66451.c:(.text+0x105): undefined reference to `drm_dsc_pps_payload_pack'
Select both CONFIG_DRM_DISPLAY_DP_HELPER and CONFIG_DRM_DISPLAY_HELPER to
ensure the helper function is always available.
Fixes: a6dfab2738 ("drm/panel: Add driver for Visionox r66451 panel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719130940.659837-1-arnd@kernel.org
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the drm panel drivers from always returning zero in the
remove callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507162616.1368908-36-u.kleine-koenig@pengutronix.de
