[ Upstream commit f5e9bda03a ]
When orientation switch is enabled in ucsi glink, there is a xhci
probe failure seen when booting up in host mode in reverse
orientation.
During bootup the following things happen in multiple drivers:
a) DWC3 controller driver initializes the core in device mode when the
dr_mode is set to DRD. It relies on role_switch call to change role to
host.
b) QMP driver initializes the lanes to TYPEC_ORIENTATION_NORMAL as a
normal routine. It relies on the typec_switch_set call to get notified
of orientation changes.
c) UCSI core reads the UCSI_GET_CONNECTOR_STATUS via the glink and
provides initial role switch to dwc3 controller.
When booting up in host mode with orientation TYPEC_ORIENTATION_REVERSE,
then we see the following things happening in order:
a) UCSI gives initial role as host to dwc3 controller ucsi_register_port.
Upon receiving this notification, the dwc3 core needs to program GCTL from
PRTCAP_DEVICE to PRTCAP_HOST and as part of this change, it asserts GCTL
Core soft reset and waits for it to be completed before shifting it to
host. Only after the reset is done will the dwc3_host_init be invoked and
xhci is probed. DWC3 controller expects that the usb phy's are stable
during this process i.e., the phy init is already done.
b) During the 100ms wait for GCTL core soft reset, the actual notification
from PPM is received by ucsi_glink via pmic glink for changing role to
host. The pmic_glink_ucsi_notify routine first sends the orientation
change to QMP and then sends role to dwc3 via ucsi framework. This is
happening exactly at the time GCTL core soft reset is being processed.
c) When QMP driver receives typec switch to TYPEC_ORIENTATION_REVERSE, it
then re-programs the phy at the instant GCTL core soft reset has been
asserted by dwc3 controller due to which the QMP PLL lock fails in
qmp_combo_usb_power_on.
d) After the 100ms of GCTL core soft reset is completed, the dwc3 core
goes for initializing the host mode and invokes xhci probe. But at this
point the QMP is non-responsive and as a result, the xhci plat probe fails
during xhci_reset.
Fix this by passing orientation switch to available ucsi instances if
their gpio configuration is available before ucsi_register is invoked so
that by the time, the pmic_glink_ucsi_notify provides typec_switch to QMP,
the lane is already configured and the call would be a NOP thus not racing
with role switch.
Cc: stable@vger.kernel.org
Fixes: c6165ed2f4 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Suggested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240301040914.458492-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6aaceb7d9c upstream.
Some DELL systems don't like UCSI_ACK_CC_CI commands with the
UCSI_ACK_CONNECTOR_CHANGE but not the UCSI_ACK_COMMAND_COMPLETE
bit set. The current quirk still leaves room for races because
it requires two consecutive ACK commands to be sent.
Refactor and significantly simplify the quirk to fix this:
Send a dummy command and bundle the connector change ack with the
command completion ack in a single UCSI_ACK_CC_CI command.
This removes the need to probe for the quirk.
While there define flag bits for struct ucsi_acpi->flags in ucsi_acpi.c
and don't re-use definitions from ucsi.h for struct ucsi->flags.
Fixes: f3be347ea4 ("usb: ucsi_acpi: Quirk to ack a connector change ack cmd")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-5-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15b2e71b46 upstream.
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 165376f6b2 upstream.
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197331b27a upstream.
While commit 69f89168b3 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b3 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23b1d2d99b upstream.
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3be347ea4 ]
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 69f89168b3 upstream.
Since the merge of b717dfbf73 ("Revert "usb: typec: tcpm: fix
cc role at port reset"") into mainline the LibreTech Renegade
Elite/Firefly has died during boot, the main symptom observed in testing
is a sudden stop in console output. Gábor Stefanik identified in review
that the patch would cause power to be removed from devices without
batteries (like this board), observing that while the patch is correct
according to the spec this appears to be an oversight in the spec.
Given that the change makes previously working systems unusable let's
revert it, there was some discussion of identifying systems that have
alternative power and implementing the standards conforming behaviour in
only that case.
Fixes: b717dfbf73 ("Revert "usb: typec: tcpm: fix cc role at port reset"")
Cc: stable <stable@kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240212-usb-fix-renegade-v1-1-22c43c88d635@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e39 upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9aed03a0a upstream.
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b717dfbf73 upstream.
This reverts commit 1e35f07439.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f07439 ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5962ded777 upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released is a plug evaluates
against the released altmode's partner instead of the calling altmode, so
change adev in typec_altmode_put_partner to properly refer to the altmode
being released.
Because typec_altmode_set_partner calls get_device() on the port altmode,
add partner_adev that points to the port altmode in typec_put_partner to
call put_device() on. typec_altmode_set_partner is not called for port
altmodes, so add a check in typec_altmode_release to prevent
typec_altmode_put_partner() calls on port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: <stable@vger.kernel.org>
Co-developed-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Tested-by: Christian A. Ehrhardt <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240103181754.2492492-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b17b7fe6dd upstream.
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4987daf86c upstream.
It is possible that typec_register_partner() returns ERR_PTR on failure.
When port->partner is an error, a NULL pointer dereference may occur as
shown below.
[91222.095236][ T319] typec port0: failed to register partner (-17)
...
[91225.061491][ T319] Unable to handle kernel NULL pointer dereference
at virtual address 000000000000039f
[91225.274642][ T319] pc : tcpm_pd_data_request+0x310/0x13fc
[91225.274646][ T319] lr : tcpm_pd_data_request+0x298/0x13fc
[91225.308067][ T319] Call trace:
[91225.308070][ T319] tcpm_pd_data_request+0x310/0x13fc
[91225.308073][ T319] tcpm_pd_rx_handler+0x100/0x9e8
[91225.355900][ T319] kthread_worker_fn+0x178/0x58c
[91225.355902][ T319] kthread+0x150/0x200
[91225.355905][ T319] ret_from_fork+0x10/0x30
Add a check for port->partner to avoid dereferencing a NULL pointer.
Fixes: 5e1d4c49fb ("usb: typec: tcpm: Determine common SVDM Version")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Link: https://lore.kernel.org/r/20231020012132.100960-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some OEM systems, adding a W7900 dGPU triggers RAS errors and hangs
at a black screen on startup. This issue occurs only if `ucsi_acpi` has
loaded before `amdgpu` has loaded. The reason for this failure is that
`amdgpu` uses power_supply_is_system_supplied() to determine if running
on AC or DC power at startup. If this value is reported incorrectly the
dGPU will also be programmed incorrectly and trigger errors.
power_supply_is_system_supplied() reports the wrong value because UCSI
power supplies provided as part of the system don't properly report the
scope as "DEVICE" scope (not powering the system).
In order to fix this issue check the capabilities reported from the UCSI
power supply to ensure that it supports charging a battery and that it can
be powered by AC. Mark the scope accordingly.
Cc: stable@vger.kernel.org
Fixes: a7fbfd44c0 ("usb: typec: ucsi: Mark dGPUs as DEVICE scope")
Link: https://www.intel.com/content/www/us/en/products/docs/io/universal-serial-bus/usb-type-c-ucsi-spec.html p28
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009184643.129986-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon receiving an ACK for a sent EXIT_MODE message, the DisplayPort
driver currently resets the status and configuration of the port partner.
The hpd signal is not updated despite being part of the status, so the
Display stack can still transmit video despite typec_altmode_exit placing
the lanes in a Safe State.
Set hpd to low when a sent EXIT_MODE message is ACK'ed.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231009210057.3773877-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The try_src_count and try_snk_count may still be 1 after enter into
unattached state. This may be caused by below case:
- SNK_TRY->SNK_TRY_WAIT->SRC_TRYWAIT->SNK_UNATTACHED
- SRC_TRY->SRC_TRY_WAIT->SNK_TRYWAIT->SNK_UNATTACHED
The port->attached is not true at the end and tcpm_reset_port() will not
be called. This will reset counter into for these cases, otherwise the tcpm
won't try role when new cable attached.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230820151518.1403006-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending Discover Identity messages to a Port Partner that uses Power
Delivery v2 and SVDM v1, we currently send PD v2 messages with SVDM v2.0,
expecting the port partner to respond with its highest supported SVDM
version as stated in Section 6.4.4.2.3 in the Power Delivery v3
specification. However, sending SVDM v2 to some Power Delivery v2 port
partners results in a NAK whereas sending SVDM v1 does not.
NAK messages can be handled by the initiator (PD v3 section 6.4.4.2.5.1),
and one solution could be to resend Discover Identity on a lower SVDM
version if possible. But, Section 6.4.4.3 of PD v2 states that "A NAK
response Should be taken as an indication not to retry that particular
Command."
Instead, we can set the SVDM version to the maximum one supported by the
negotiated PD revision. When operating in PD v2, this obeys Section
6.4.4.2.3, which states the SVDM field "Shall be set to zero to indicate
Version 1.0." In PD v3, the SVDM field "Shall be set to 01b to indicate
Version 2.0."
Fixes: c34e85fa69 ("usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230731165926.1815338-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the embedded cases, the DisplayPort connector is handled by the TCPM
itself. It was proposed to add the "displayport" OF property to the DT
bindings, but it was rejected in favour of properly describing the
electrical signal path using of_graph.
Fallback to the controller fwnode for HPD notifications to
support such usecases without requiring additional DT properties.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230817150824.14371-2-dmitry.baryshkov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When connecting to some DisplayPort partners, the initial status update
after entering DisplayPort Alt Mode notifies that the DFP_D/UFP_D is not in
the connected state. This leads to sending a configure message that keeps
the device in USB mode. The port partner then sets DFP_D/UFP_D to the
connected state and HPD to high in the same Attention message. Currently,
the HPD signal is dropped in order to handle configuration.
This patch saves changes to the HPD signal when the device chooses to
configure during dp_altmode_status_update, and invokes sysfs_notify if
necessary for HPD after configuring.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230726020903.1409072-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230712085722.1414743-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design of the PPS APDO selection, TCPM power supply only
accepts the requested voltage which is inside the range of the selected
PPS profile. To extend the flexibility and usability, remove the checks
about the voltage range in current profile. And try to search all PPS
APDOs of the Source that fit the requested voltage.
Also remove some redundant checks in tcpm_pd_build_pps_request.
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230731162159.19483-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
